Argent Data Systems OpenTracker USB Manuel d'utilisateur

Argent Data Systems Tracker3 Family User’s Manual Revised 1-3-2014 Argent Data Systems, Inc. PO Box 579 Santa Maria, CA 93456-0579 USA (800)

Tracker3 User’s Manual 8 inputs, a counter/transmit trigger input, a digital I/O pin, and a 7-amp solid state relay output. 5.2. Rear Panel The

Tracker3 User’s Manual 9 6. Connections 6.1. SERIAL Connector 2: Data in (port A) 3: Data out (port A) 4: Power output for GPS 5:

Tracker3 User’s Manual 10 7. Jumper Settings A jumper block on the OT3m board provides the following settings: Voltage select – ‘5’. Connects

Tracker3 User’s Manual 11 8. Hardware Description – T3-135 The Tracker3 model T3-135 is a plug-in board for the Alinco DR-135T. It can also be

Tracker3 User’s Manual 12 9. Hardware Description – T3-Mini The T3-Mini is an embeddable tracker module measuring 1.72" by 1.12" (43m

Tracker3 User’s Manual 13 10. Hardware Description – T3-301 The T3-301 is a Friendcom FC-301/D 5-watt data radio module with a Tracker3 series

Tracker3 User’s Manual 14 10.2. Radio Configuration Two special commands are available from the T3-301’s command line for setting the radio fr

Tracker3 User’s Manual 15 sudo modprobe usbserial vendor=0x134a product=0x9000 11. Setup and Configuration You can use a PC to connect to the

Tracker3 User’s Manual 16 Other modern operating systems should be able to use the tracker as a generic CDC ACM serial device. Its VID is 0x134

Tracker3 User’s Manual 17 KISS – In KISS mode, a PC or other host device sends and receives raw AX.25 packets. Keep in mind that even with one

FCC Part 15 Notice This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions: this device may n

Tracker3 User’s Manual 18 14. Remote Access Commands can be issued to the Tracker3 remotely via APRS messages. The originating station’s call

Tracker3 User’s Manual 19 exit safe mode, use the RESET command or power off the tracker after removing the jumper used to enter safe mode. The

Tracker3 User’s Manual 20 Also, should a valid password be sent without being received by the target device, an eavesdropper would know the next

Tracker3 User’s Manual 21 OTWINCFG Configuration Program The Tracker3 can be configured using the otwincfg.exe program under Windows. The prog

Tracker3 User’s Manual 22 17.4. Warm Boot vs. Cold Boot If the unit is already powered on and operating when you click the ‘Connect’ button, th

Tracker3 User’s Manual 23 17.7. Configuration Profiles The Tracker3 can store two separate configuration profiles. The profile currently being

Tracker3 User’s Manual 24 Alternate Paths - When enabled, this option causes the tracker to alternate between the paths specified in either prof

Tracker3 User’s Manual 25 Voltage – Report input voltage in the comment field. The maximum value is 18.5 volts, and the minimum is the dropout

Tracker3 User’s Manual 26 Use PTT Input – When this checkbox is enabled, the tracker can be connected inline with a microphone to operate in b

Tracker3 User’s Manual 27 useful for applications like high altitude balloons that may lose GPS lock after landing, but still need to transmit t

Tracker3 User’s Manual 1 1. Introduction ...

Tracker3 User’s Manual 28 Reset on Transmit – Setting this checkbox causes the counter to reset with every transmission. Hence, the count report

Tracker3 User’s Manual 29 No Suppress PTT Out on PTT In – This option allows the tracker to be used in burst-after-voice mode without breaking

Tracker3 User’s Manual 30 17.11. Access List This screen allows editing of the tracker’s remote access control list. 17.12. Profile Switchi

Tracker3 User’s Manual 31 equal to). Clicking on the button showing the comparison operator toggles it between these two settings. The Altitude

Tracker3 User’s Manual 32 The ‘Digipeat on my call’ option causes the tracker to repeat packets with the tracker’s own callsign in the packet’s

Tracker3 User’s Manual 33 18. Command Reference Most commands can be issued through the serial console, APRS message, or fleet management mess

Tracker3 User’s Manual 34 ANALOG <n> Returns the current reading for the specified analog input pin. See the telemetry section of this m

Tracker3 User’s Manual 35 CALIBRATE LOW | HIGH | ALT | PACKET (local only) Calibration functions to set demodulator tuning and transmitt

Tracker3 User’s Manual 36 CUSTSYM on|off Enables the use of custom symbols if they have been uploaded to a compatible Garmin GPS receiver (using

Tracker3 User’s Manual 37 ECHO [text] Prints text to the console. Allows output from scripts when using the USB console. EXTSQL on | off Enab

Tracker3 User’s Manual 2 17.7. Configuration Profiles ... 23 17.8.

Tracker3 User’s Manual 38 Selects transmission baud rate. Note that the reception baud rate is fixed at 1200 baud. Return value: 99 = invalid s

Tracker3 User’s Manual 39 PASSALL on|off Normally the Tracker3 ignores all received packets that fail a frame check sequence test. PASSALL di

Tracker3 User’s Manual 40 PROFILE 1 | 2 Selects the configuration profile to use. If profile switching is enabled, the profile switching parame

Tracker3 User’s Manual 41 REQALL on|off Require all configuration switch parameters to be met before switching profiles. RESET Perform software

Tracker3 User’s Manual 42 The <low speed> and <high speed> settings define these two limits. For storage efficiency, the speeds are

Tracker3 User’s Manual 43 STATUS <0-255> Status packets are sent every n transmissions, or if set to 0, status text is sent as part of the

Tracker3 User’s Manual 44 TXLEVEL <1-255> Sets transmission audio level. This value should be selected to provide an appropriate FM dev

Tracker3 User’s Manual 45 19. Telemetry All Tracker3 models have the ability to send telemetry information from their on-board sensors, and so

Tracker3 User’s Manual 46 20. Script System The Tracker3’s script engine allows simple programs to be run on the tracker to customize the trac

Tracker3 User’s Manual 47 The highlighted line in the script listing shows where the next command will be inserted. The 'Delete Line&apos

Tracker3 User’s Manual 3 1. Introduction The Tracker3 family includes the stand-alone OT3m model, the T3-135 internal board for the Alinco DR-1

Tracker3 User’s Manual 48 To compare the current altitude to a fixed value, for example, you can select "Altitude" in box A and enter

Tracker3 User’s Manual 49 On Startup Executes a block of code only once, immediately after the tracker is powered on. On Second Executes a b

Tracker3 User’s Manual 50 Use this command carefully - the tracker's flash memory has a write endurance of about 100,000 cycles, and any co

Tracker3 User’s Manual 51 These general-purpose counters have no predefined meaning, and they have no effect on the rest of the system. Ticks

Tracker3 User’s Manual 52 21. UI-View32 Setup For use with the UI-View32 APRS client, either port of the Tracker3 can be set manually to KISS

Tracker3 User’s Manual 53 No ‘Into KISS’ or ‘Exit KISS’ commands are needed, and any settings in these fields should be deleted. Placing a ‘0’

Tracker3 User’s Manual 4 connection and a radio, pass traffic from the radio network to a shared, worldwide APRS stream. Many IGates will pass

Tracker3 User’s Manual 5 Another option is an APRS-capable radio, like those sold by Kenwood and Yaesu. These radios have a text display, but r

Tracker3 User’s Manual 6 4. Major Features APRS Tracker - The Tracker3 is first and foremost a full-featured APRS tracker. It works with GPS r

Tracker3 User’s Manual 7 Telemetry – All Tracker3 models include an integrated temperature sensor. The OT3m and T3-301 can measure and report